Always Mobile

Always Mobile

Edmonton 780-448-9498

Calgary 403-770-5625

Thermalex 2000

Commercial / Industrial Sectional Overhead Doors

Specifically Designed for Commercial / Industrial Applications

The Thermalex 2000 Series is specifically designed and built for commercial and industrial applications. Using only the highest quality materials, steel panels are manufactured to strict tolerances on a fully automated continuous foamed-in-place line. This results in a durable, clean and consistent finished product, which offers exceptional value. This Edmonton commercial door solution is ready to go when you are.

Features & Benefits

Thermalex TX380 1,1/2" (38mm) Thermalex TX450 1,3/4" (44.5mm) Thermalex TX450-20 1,3/4" (44.5mm) Thermalex TX500
2" (50.8mm)
Insulation Type / Foam Process Polyurethane / Continuous Polyurethane / Continuous Polyurethane / Continuous Polyurethane / Continuous
R-Value / U-Value 14.1 / 0.07 + 16.3 / 0.06 + 16.3 / 0.06 + 18.4 / 0.05 +
Thermal Break
(between ext & int skins)
Chemically Bonded & Sealed Chemically Bonded & Sealed Chemically Bonded & Sealed Chemically Bonded & Sealed
Section Joint Shiplap w/ dual-fin weather seal Tongue & Groove w/ dual-fin weather seal Tongue & Groove w/ dual-fin weather seal Tongue & Groove w/ dual-fin weather seal
Gauge Steel Skins - min (exterior / interior) 26/26 26/26 20/26 26/26
Horizontal Hinge Plate(s) (reinforcement strip) One continuous 1,1/4" (31.8mm) 20ga Strip Two continuous 1,1/4" (31.8mm) 20ga Strips Two continuous 1,1/4" (31.8mm) 20ga Strips Two continuous 1,1/4" (31.8mm) 20ga Strips
End Stiles - Galvanized 20ga 20ga or 16ga 20ga or 16ga 20ga or 16ga
Colours Available
(interior always white)
Bright White / Brown Bright White / Brown Bright White only Bright White only
Panel Appearance (texture) Horizontal Ribs (Stucco Embossed) Horizontal Ribs (Stucco Embossed) Flush - No Ribs (Stucco Embossed) Horizontal Ribs (Stucco Embossed)
Maximum Standard Width 16'2" (4928mm) ** 28'0" (8534mm) ** 24'6" (7468mm) ** 28'0" (8534mm) **
Maximum Standard Height 16'0" (4877mm) ** 20'0" (6096mm) ** 20'0" (6096mm) ** 20'0" (6096mm) **
Insulated Windows Sealed Units
18" x 8" or 24" x 12"
Sealed Units
18" x 8" or 24" x 12"
Sealed Units
18" x 8" or 24" x 12"
Sealed Units
18" x 8" or 24" x 12"
Full View Aluminum Sections N/A White / Brown Insulated Sealed Glass White / Brown Insulated Sealed Glass N/A
** Consult Door Surgeon at 780-448-9498 for special applications and larger available sizes.
+ Calculated Value

Model U100: Solid Insulated Door

Model R112G: Thermal Commercial Door Windows

Model V130G: Full View Overhead Door Sections

Pass Door (optional - only available in TX450)

Standard Window Schedule

Height Schedule

Door Height # of Sections
8'1" 4
10'1" 5
12'1" 6
14'1" 7
16'1" 8
18'1" 9
20'1" 10
Door Width Max # of Windows
18" x 8" frame
Max # of Windows
24" x 12" frame
8' 2" 3 2
10' 2" 4 3
12' 2" 4 3
14' 2" 5 4
16' 2" 5 4
18' 2" 6 5
20' 2" 6 5
22' 2" 7 6
24' 2" 8 6

Insulated Commercial Overhead Doors

Standard Lift

High Lift

Vertical Lift

Low Headroom Lift

Lift Type Specific
Parameters
Headroom * Side Room * Backroom *
2" Track 3" Track 2" Track 3" Track 2" and 3" Track
12" radius 15" radius 15" radius Angle Mount Bracket Mount Angle Mount Bracket Mount
Standard Lift Door Height
up to 18' (5.49m)
13" (330mm) 16" (406mm) 18" (457mm) 3.25" (83mm) 3.75" (95mm) 3.5" (89mm) 4.25" (108mm) Door Height + 18" (457mm)
Door Height
above 18' (5.49m)
N/A N/A 20" (508mm)
Vertical Lift Max Door Height 28' (8.53m) Door Height = 18" (457mm) 3.25" (83mm) 3.75" (95mm) 3.5" (89mm) 4.25" (108mm) 18" (457mm)
High Lift High Lift up to 54" (1.37m) N/A Hi Lift + 9.5" (241mm) Hi Lift + 11.5" (292mm) 3.25" (83mm) 3.75" (95mm) 3.5" (89mm) 4.25" (108mm) Door Height - Hi Lift + 30" (762mm)
High Lift up to 120" (3.05m) N/A Hi Lift + 11.5" (292mm) Hi Lift + 12.5" (318mm)
High Lift up to 164" (4.17m) N/A Hi Lift + 12" (305mm) Hi Lift + 13.5" (343mm)
Low Headroom Max Door Height 18' (5.49m) Torsion in front 10" (254mm) 12" (305mm) 8" (203mm) 7" (178mm) 8" (203mm) 8" (203mm) Door Height + 18" (457mm)
Torsion in rear 6" (152mm) N/A
* Minimum requirement for normal installation conditions

Sectional Doors

Doors shall be Thermalex Series TX380, TX450, TX450-20, TX500 - Thermalex Models U100, R112G, V130G as manufactured by Upwardor Corporation. Operation shall be manual push-up operation and include sections, track, brackets and hardware to suit door opening and headroom available.

Related Work

All framing work, spring pads, frame extensions, caulking and electrical wiring shall be under other divisions.

Door Sections

Door Sections shall be roll-formed continuous steel sheets, corrosion resistant Z275 ASTM, stucco embossed, and ribbed for added strength. Exterior steel skins shall be prefinished in bright white or brown with bright white interior skin. Paint finihs shall be of Polyester. TX450, TX450-20 and TX500 door sections shall have a Tongue and Groove Joint with dual fin weather strip between section joints. TX380 door sections shall have a shiplap joint also with dual fin weather strip between section joints.

Door sections shall be thermally broken and chemically sealed and bonded for added weather resistance. Sections shall be polyurethan insulated (Zero ODP) foamed-in-place by means of Continuous Process. Interior skin of each TX450, TX450-2- and TX500 section shall be reinforced by two continuous 1,1/4" (32mm) wide steel strips, 20 gauge, at top and bottom of section for mounting of either half or full hinge. TX380 sections shall have continuous hinge strip reinforcement at top and bottom of section for mounting of half hinge.

Glazing

Glazing for Model R112G shall be of 1/8" (3mm) thermopane sealed unit, clear, fitted into 18" x 8" (457mm x 203mm) or 24" x 12" (609mm x 308mm) moulded plastic frame in black or white. V130G aluminum framed full view section shall be glazed with 1/8" (3mm) thermopane sealed unit (overall thickness 1/2" with 1/4" air space), clear, fitted with removable moulding for easy replacement.

Note: other glazing options available, please consult Doors Surgeon at 780-448-9498.

Hardware

Upwardor Corp. hardware shall be of galvanized steel, G60 ASTM, with gauge thickness to suit applications and shall be in accordance with drawins and specifications.

Tracks

Tracks shall be 2" (51mm) minimum, 14 gauge, or 3" (76mm) minimum, 12 gauge. All vertical tracks shall be bolted and assembled to a continuous 2" (51mm) x 4" (102mm) vertical angle, minimum 14 gauge, or to jamb brackets, 11 gauge, and shall be fully adjustable. Horizontal tracks shall have a maximum radius of 15" (381mm) with a continuous 12 gauge angle, 1,1/2" (38mm) x 2" (51mm), welded to the horizontal tracks.

Hinges / Roller

Roller carriers shall be a minimum of 13 gauge galvanized steel to suit door width. Doors 16' (4877mm) wide and over require double end hinges, along with strut bar reinforcement. Rollers shall be of 2" (51mm) or 3" (76mm) diameter, 10 ball bearing with hardened raceway and cold rolled 7/16" (11mm) x 4,1/2" (114mm) stem. Long stem 7" (178mm) rollers shall be supplied with double end hinges.

Torsion Springs

Torsion springs shall be oil tempered with minimum 10,000 standard cyclage (specify higher cyclage if required to maximum of 100,000 cycles) fitted on a continuous 1" (25mm) hollow, 14 gauge tube shaft, or on a 1" (25mm) cold rolled solid shaft, keyed and mounted on ball bearings, supported by heavy gauge gusset plates. Counter weight system available on request. For added strength, 1,1/4" (32mm) diameter solid shaft and pillow block bearings also available.

Cable Drums

Cable drums shal suit the type of lift required and be able to withstand maximum cycle requirements. Cables shall be of galvanized aircraft grade, 7 x 19 construction, designed to suit door weight at a safety factor of 8 to 1.

Note: When specifying Chain Hoist or Jack Shaft Electrical operator on standard lift doors, specify solid shaft, spreader bars and pusher springs.

© Door Surgeon 2018 | No content may be used without permission.