Always Mobile

Always Mobile

Edmonton 780-448-9498

Calgary 403-770-5625

Door Surgeon New Commercial Industrial Overhead Garage Doors Edmonton

New overhead garage doors for warehouses, car-washes and loading docks supplied and installed

Door Surgeon's mobile commercial industrial overhead service installers can supply and install new overhead garage doors to replace your broken or damaged overhead garage door, panels, tracks, hinges, rollers, cables and springs. Call Door Surgeon's overhead garage door sales and service centre to discuss your commercial/industrial overhead garage door needs for warehouses, carwashes, apartment parkades, commercial buildings.


Thermalex 2000

New Commercial / Industrial Overhead Garage Doors



Specifically Designed for Commercial / Industrial Applications

The Thermalex 2000 Series is specifically designed and built for commercial and industrial applications. Using only the highest quality materials, steel panels are manufactured to strict tolerances on a fully automated continuous foamed-in-place line. This results in a durable, clean and consistent finished product, which offers exceptional value. Door Surgeon's mobile commercial industrial overhead garage door installation serviceman can visit your jobsite and help determine the new overhead garage door replacement that meets the requirements of your loading dock, warehouse, commercial building or apartment overhead garage door renovation and replacement needs.


Features & Benefits

Thermalex TX380 1,1/2" (38mm) Thermalex TX450 1,3/4" (44.5mm) Thermalex TX450-20 1,3/4" (44.5mm) Thermalex TX500
2" (50.8mm)
Insulation Type / Foam Process Polyurethane / Continuous Polyurethane / Continuous Polyurethane / Continuous Polyurethane / Continuous
R-Value / U-Value 14.1 / 0.07 + 16.3 / 0.06 + 16.3 / 0.06 + 18.4 / 0.05 +
Thermal Break
(between ext & int skins)
Chemically Bonded & Sealed Chemically Bonded & Sealed Chemically Bonded & Sealed Chemically Bonded & Sealed
Section Joint Shiplap w/ dual-fin weather seal Tongue & Groove w/ dual-fin weather seal Tongue & Groove w/ dual-fin weather seal Tongue & Groove w/ dual-fin weather seal
Gauge Steel Skins - min (exterior / interior) 26/26 26/26 20/26 26/26
Horizontal Hinge Plate(s) (reinforcement strip) One continuous 1,1/4" (31.8mm) 20ga Strip Two continuous 1,1/4" (31.8mm) 20ga Strips Two continuous 1,1/4" (31.8mm) 20ga Strips Two continuous 1,1/4" (31.8mm) 20ga Strips
End Stiles - Galvanized 20ga 20ga or 16ga 20ga or 16ga 20ga or 16ga
Colours Available
(interior always white)
Bright White / Brown Bright White / Brown Bright White only Bright White only
Panel Appearance (texture) Horizontal Ribs (Stucco Embossed) Horizontal Ribs (Stucco Embossed) Flush - No Ribs (Stucco Embossed) Horizontal Ribs (Stucco Embossed)
Maximum Standard Width 16'2" (4928mm) ** 28'0" (8534mm) ** 24'6" (7468mm) ** 28'0" (8534mm) **
Maximum Standard Height 16'0" (4877mm) ** 20'0" (6096mm) ** 20'0" (6096mm) ** 20'0" (6096mm) **
Insulated Windows Sealed Units
18" x 8" or 24" x 12"
Sealed Units
18" x 8" or 24" x 12"
Sealed Units
18" x 8" or 24" x 12"
Sealed Units
18" x 8" or 24" x 12"
Full View Aluminum Sections N/A White / Brown Insulated Sealed Glass White / Brown Insulated Sealed Glass N/A
** Consult Door Surgeon at 780-448-9498 for special applications and larger available sizes.
+ Calculated Value

Model U100: Solid Insulated Door

Model R112G: Thermal Commercial Door Windows

Model V130G: Full View Overhead Door Sections

Pass Door (optional - only available in TX450)


Standard Window Chart

Standard Height Chart

Door Height # of Sections
8'1" 4
10'1" 5
12'1" 6
14'1" 7
16'1" 8
18'1" 9
20'1" 10
Door Width Max # of Windows
18" x 8" frame
Max # of Windows
24" x 12" frame
8' 2" 3 2
10' 2" 4 3
12' 2" 4 3
14' 2" 5 4
16' 2" 5 4
18' 2" 6 5
20' 2" 6 5
22' 2" 7 6
24' 2" 8 6

Insulated Commercial Overhead Doors


Standard Lift Measurements

Standard Lift

High Lift

Vertical Lift

Low Headroom Lift

Lift Type Specific
Parameters
Headroom * Side Room * Backroom *
2" Track 3" Track 2" Track 3" Track 2" and 3" Track
12" radius 15" radius 15" radius Angle Mount Bracket Mount Angle Mount Bracket Mount
Standard Lift Door Height
up to 18' (5.49m)
13" (330mm) 16" (406mm) 18" (457mm) 3.25" (83mm) 3.75" (95mm) 3.5" (89mm) 4.25" (108mm) Door Height + 18" (457mm)
Door Height
above 18' (5.49m)
N/A N/A 20" (508mm)
Vertical Lift Max Door Height 28' (8.53m) Door Height = 18" (457mm) 3.25" (83mm) 3.75" (95mm) 3.5" (89mm) 4.25" (108mm) 18" (457mm)
High Lift High Lift up to 54" (1.37m) N/A Hi Lift + 9.5" (241mm) Hi Lift + 11.5" (292mm) 3.25" (83mm) 3.75" (95mm) 3.5" (89mm) 4.25" (108mm) Door Height - Hi Lift + 30" (762mm)
High Lift up to 120" (3.05m) N/A Hi Lift + 11.5" (292mm) Hi Lift + 12.5" (318mm)
High Lift up to 164" (4.17m) N/A Hi Lift + 12" (305mm) Hi Lift + 13.5" (343mm)
Low Headroom Max Door Height 18' (5.49m) Torsion in front 10" (254mm) 12" (305mm) 8" (203mm) 7" (178mm) 8" (203mm) 8" (203mm) Door Height + 18" (457mm)
Torsion in rear 6" (152mm) N/A
* Minimum requirement for normal installation conditions

Sectional Doors

Doors shall be Thermalex Series TX380, TX450, TX450-20, TX500 - Thermalex Models U100, R112G, V130G as manufactured by Upwardor Corporation. Operation shall be manual push-up operation and include sections, track, brackets and hardware to suit door opening and headroom available.

Related Work

All framing work, spring pads, frame extensions, caulking and electrical wiring shall be under other divisions.

Door Sections

Door Sections shall be roll-formed continuous steel sheets, corrosion resistant Z275 ASTM, stucco embossed, and ribbed for added strength. Exterior steel skins shall be prefinished in bright white or brown with bright white interior skin. Paint finihs shall be of Polyester. TX450, TX450-20 and TX500 door sections shall have a Tongue and Groove Joint with dual fin weather strip between section joints. TX380 door sections shall have a shiplap joint also with dual fin weather strip between section joints.

Door sections shall be thermally broken and chemically sealed and bonded for added weather resistance. Sections shall be polyurethan insulated (Zero ODP) foamed-in-place by means of Continuous Process. Interior skin of each TX450, TX450-2- and TX500 section shall be reinforced by two continuous 1,1/4" (32mm) wide steel strips, 20 gauge, at top and bottom of section for mounting of either half or full hinge. TX380 sections shall have continuous hinge strip reinforcement at top and bottom of section for mounting of half hinge.

Glazing

Glazing for Model R112G shall be of 1/8" (3mm) thermopane sealed unit, clear, fitted into 18" x 8" (457mm x 203mm) or 24" x 12" (609mm x 308mm) moulded plastic frame in black or white. V130G aluminum framed full view section shall be glazed with 1/8" (3mm) thermopane sealed unit (overall thickness 1/2" with 1/4" air space), clear, fitted with removable moulding for easy replacement.

Note: other glazing options available, please consult Doors Surgeon at 780-448-9498.

Hardware

Upwardor Corp. hardware shall be of galvanized steel, G60 ASTM, with gauge thickness to suit applications and shall be in accordance with drawins and specifications.

Tracks

Tracks shall be 2" (51mm) minimum, 14 gauge, or 3" (76mm) minimum, 12 gauge. All vertical tracks shall be bolted and assembled to a continuous 2" (51mm) x 4" (102mm) vertical angle, minimum 14 gauge, or to jamb brackets, 11 gauge, and shall be fully adjustable. Horizontal tracks shall have a maximum radius of 15" (381mm) with a continuous 12 gauge angle, 1,1/2" (38mm) x 2" (51mm), welded to the horizontal tracks.

Hinges / Roller

Roller carriers shall be a minimum of 13 gauge galvanized steel to suit door width. Doors 16' (4877mm) wide and over require double end hinges, along with strut bar reinforcement. Rollers shall be of 2" (51mm) or 3" (76mm) diameter, 10 ball bearing with hardened raceway and cold rolled 7/16" (11mm) x 4,1/2" (114mm) stem. Long stem 7" (178mm) rollers shall be supplied with double end hinges.

Torsion Springs

Torsion springs shall be oil tempered with minimum 10,000 standard cyclage (specify higher cyclage if required to maximum of 100,000 cycles) fitted on a continuous 1" (25mm) hollow, 14 gauge tube shaft, or on a 1" (25mm) cold rolled solid shaft, keyed and mounted on ball bearings, supported by heavy gauge gusset plates. Counter weight system available on request. For added strength, 1,1/4" (32mm) diameter solid shaft and pillow block bearings also available.

Cable Drums

Cable drums shal suit the type of lift required and be able to withstand maximum cycle requirements. Cables shall be of galvanized aircraft grade, 7 x 19 construction, designed to suit door weight at a safety factor of 8 to 1.

Note: When specifying Chain Hoist or Jack Shaft Electrical operator on standard lift doors, specify solid shaft, spreader bars and pusher springs.


Therma Series

New Commercial / Industrial Insulated Overhead Garage Doors



Cost Effective

Designed to provide cost effective insulated overhead garage door solutions. Effective in commercial garage door renovation and new construction applications. Door Surgeon's mobile commercial overhead garage door installation serviceman can come to your apartment, warehouse, loading dock and commercial overhead garage door. Door Surgeon's mobile service man can recommend the appropriate replacement overhead garage door to match your needs and budget.


Long Term Insulation

Roll formed hot dipped G40 galvanized steel. Door sections are sandwich construction and insulated with expanded polystyrene. Sections are thermally broken and have a thermal barrier joint seal between door sections. Compressible loop-type PVC bottom weather seal secured with extruded aluminum retainer extending the full width of the door. Door widths are available up to 24'2". Door heights are available up to 16' in 3" increments using 21" and 24" section heights.

Models


Window Options

Door Surgeon's selection of overhead garage doors can be provided with windows that are supplied with 1/8" clear annealed single pane glass. Optional single pane tempered, textured, coloured and insulated glass.

(A) Aluminum Full View Sections

(Mill Finish Std. Anodized & Painted Finish Optional) Note: Full-View sections not available on Model 650

(B) Vision Lite

* 33,1/4"W x 14,1/4"H

(C) Standard Lite

* 17,1/4"W x 11,1/4"H

(D) Security Lite

* 18,3/4"W x 5,1/2"H

* Visible viewing area through the windows


Construction

Our time proven sandwich construction method creates a very rigid door and forms a natural thermal-break for additional energy efficiency.

Tongue & Groove weather joint
with Thermal Break.

Energy efficient thermal barrier
joint seal on 2" & 3" thick doors.

Flexible PVC Weather Seal with
Adjustable Aluminum Retainer.

Finish

Exterior commercial door face will receive a four-coat protections system. This shall consist of:

Garage Door Spring Assembly

The spring counterbalance assembly consists of:

Hardware

Assembled commercial doors with specified hardware meet or exceed the wind load standards established under ANSI/DASMA specification 102-2004. All hardware components are hot-dipped galvanized with the exception of rollers. All components meet ASTM A526 standards.

Commercial Door Track Assembly

Tracks are commercial quality steel, standard as per ASTM A-526, G60 galvanized, 2" or 3" in size and 16 gauge to 12 gauge depending on the door size and weight. The vertical tracks shall be graduated and provide and adjustable wedge-type closing action. The gorizontal track will be reinforced with angle of adequate length and gauge to help prevent deflection. Additional bracing shall be provided by the installer to prevent deflection and establish a rigid installation.

Options

High Cycle and Extended Life Applications.


Standard Lift

High Lift

Vertical Lift

Low Headroom Lift


SunShine Doors

New Commercial / Industrial View-Through Overhead Doors



New Industrial Overhead Garage Doors for car washes and restaurants

Door Surgeon's mobile overhead garage door serviceman can provide you with information and options that will get you the best glass or polycarbonite overhead garage door that can be used to provide full view restaurant doors and or water resistant car wash doors, this new commercial overhead garage door selection will get the job done.

Triple wall polycarbonate is virtually indestructable & energy efficient

This material offers thermal insulation, excellent impact resistance, and outstanding light transmission. Not only is it used in many garage businesses and commercial properties, it is the standard material used in greenhouses for temperature control.

SunView Door

The SunView door is a multi-sectional anodized aluminum door that can be glazed with a variety of glass choices. The SunView door is well suited for car washes, car and RV dealerships, restaurants and homes. These full view window garage doors are built to last.

Thermal Insulation

Sophisticated multi-wall construction creates an insulating air space within the internal channels, resulting in excellent energy-efficient and significant reductions in heating costs. Triple wall poly-carbonate sheet provides the highest level of thermal insulation available today in a poly-carbonate sheet material.

High Impact Resistance

Triple wall poly-carbonate shee offers extremely high impact resistance, minimizing the risk of damage or breakage resulting from fallen ice, snow, hail or dislodged roofing tiles. This sheet can also withstand constant thermal extremities, wind and building settling/movement without cracking or splitting.

Light Transmission

Triple wall poly-carbonate sheet is available in transparent colours which allow up to 82% light transmission.

Fire Performance

Unlike many thermoplastic materials, Triple wall plycarbonate sheets are CC-1 flame rated and passes E84 steinner tunnel - a significant performance advantage compared to other plastic materials.

Weather Resistant

Triple wall polycarbonate sheets offer outstanding, long term performance even after prolonged exposure to the sun, rain and snow - while maintaining its new appearance year after year.

Design Versatility

The lightweight yet rigid Triple wall poly-carbonate sheet reduces the need for extensive supporting structures, allowing for attractive, wide-span installations. And since it can be easily cold-formed, cut and shaped, you can consider imaginative glazing designs that ar virtually impossible using traditional materials.

Easy Handling and Installation

Triple wall poly-carbonate sheets are strong, yet extremely light, making it safe and easy to handle during installation. It can be cut to size using conventional workshop tools and fit into most existing glazing bars and frames.

Cleaning Instructions

Rinse sheet with lukewarm water. Wash sheet with a solution of mild soap or household detergent and lukewarm water, using a soft cloth or sponge to loosen any dirt or grime. Rinse with cold water and dry with a soft cloth to prevent spotting. Never use abrasive or highly alkaline clearners on Triple wall poly-carbonate sheets.


Laforge

Commercial Garage Doors


Premium Commercial Doors

Laforge overhead doors are positioned as our premium overhead door solution for garage door renovations or industrial door face changes. When replacing an Edmonton commercial overhead door, no finer choice can be made.

Winter Garage Doors

Laforge doors are engineered with a 1,3/4" core of polyurethane foam insulation that provides an R16 value throughout each panel. The core is permanently bonded to the twin outer face sheets with a unique high pressure, heat bonding process.

Customize your panel with either Traditional or Roll Form, or if you prefer, you may also have Flush panels, no embossments are imprinted, just the realistic wood grain look.

Cost Effective & Custom Solutions

Did you know that per square foot, adding a garage door window (thermopane) to a garage door is less expensive than adding a window to your garage wall?

We offer a variety of over head door windows. While only 3 versions are shown here, the options are virtually endless. Just like our garage doors, our window selection can be custom made to your specifications.

Our pre-finished PVC extruded frames, which are available in different colours, are designed for easy removal and reinstallation should the need arise to replace a broken pane. Held in secure with 14 zinc coated screw, our windows boast a 2 point seal system on BOTH the thermo and the door panel. These commerical over head door windows are built to last.

Garage Door Width Windows / Section
8' 2
8' - 11' 3
12' - 13' 4
14' - 16' 5
16.1' - 18' 6
18' - 22' 7
22' - 24' 8

Commercial Door Colours

Model 600 - Steel Commercial Overhead Door

Our Laforge steel skins have a 26 gauge rating. We have 4 enduring colours to choose from. Like our aluminum counterpart, each door is injected with polyurethane through a special heat bonding process to give the doors an R16 rating.

Divine White

Creamy
Sandstone

Charming
Rosewood

Heavenly
Dark Brown

Note: The accuracy of the colours displayed may vary depending on the settings of your monitor. To obtain an exact colour reference, please contact Door Surgeon at 780-448-9498 for colour samples.

Insulated Commercial Doors

Laforge doors are engineered with a 1,3/4" core of polyurethane insulation that provides up to a R16 value throughout each panel. The core is permanently bonded to the twin outer face sheets with a unique high pressure, heat bonding process.

Garage Door Weather Seals

Laforge doors are designed and manufactured for the Nordic climates. Every door is installed complete with weather seals at all points of exposure. A 3 point seal system has been developed to create a continuous barrier at each panel section.

Polyurethane Insulated Garage Door Panels

High density injected Polyurethane (CFC Free) ensures panel strength and provides an energy saving R16 value.

Wood Grain Texture

The rich wood grain texture of Laforge doors creates a finish that has the appearance and the feel of authentic wood.

Thermo Breaks

The sides of the Laforge doors are menufactured with wood blocks inserted into the inner skin to provide reinforcement for the hinges while providing added stability.

EPDM Seals / Bottom Rails

Laforge doors all come standard with the EPDM bottom seal. EPDM seals allow for extra flexibility in all weather situations to proved a greater prevention of air, snow and dust infiltration. Choose, between the standard PVC bottom rail, or an aluminum bottom rail.

Commercial Lift Track Styles

Laforge tracks are made of high quality 12 and 13 gauge galvanized steel. Shown below are 5 different lifts along with the torsion springs in place. Heavy duty tracks are available for 33T assemblies.

Standard Lift

High Lift

Vertical Lift

Inclined Lift

Low Headroom Lift

Standard headroom 21T & 22T hardware
16" for 2" tracks
Low headroom 5" rear mount - 12" front mount. Add 3" for T-bar electric operator.
Standard headroom 33T hardware
18" for 3" tracks
Low headroom 12" rear mount - 15" front mount. Add 3" for T-bar electric operator.

Specifications

Model 22 T
Use Industrial
Frequency of Use High
50 times / day
Maximum Height 15 kg/m ^2
3.07 lbs/ft ^2
Movement Types All
Galvanized track 2" x 0.075"
Heavy Duty 2" Rollers (10 ball)
13 gauge galvanized hinges
Galvanized steel cable 5/32"
2" bottom bracket
Side lock
Torsion spring
Double end bearing plate
Brackets
Solid Shaft (1")
Handle (1)
Couplings (over 8')
Model 21 T
Use Commercial
Frequency of Use Moderate
40 times / day
Maximum Height 15 kg/m ^2
3.07 lbs/ft ^2
Movement Types All
Galvanized track 2" x 0.075"
Heavy Duty 2" Rollers (10 ball)
13 gauge galvanized hinges
Galvanized steel cable 5/32"
2" bottom bracket
Side lock
Torsion spring
Double end bearing plate
Brackets
Tubing (1")
Handle (1)
Model 33 T
Use Industrial
Frequency of Use High
60 times / day
Maximum Height 20 kg/m ^2
4.16 lbs/ft ^2
Movement Types All
Galvanized track 3" x 0.109"
Heavy Duty 3" Rollers (10 ball)
13 gauge galvanized hinges
Galvanized steel cable 3/16"
3" bottom bracket
Side lock
Torsion spring
Double end bearing plate
Brackets
Solid Shaft (1")
Handle (1)
Couplings (over 8')
Model 33 TH
Use Industrial
Frequency of Use High
120 times / day
Maximum Height 20 kg/m ^2
4.16 lbs/ft ^2
Movement Types All
For material details for the Model 33TH, please call Door Surgeon at 780-448-9498

Hardware Options

21T, 22T and 33T
Aluminum bottom rail
Replacement sections
Pusher springs
Track guards
Double hinges From 8' to 14'
From 14'1" to 18'
Spring cycles From 10,000 to 25,000
From 25,001 to 50,000
From 50,001 to 100,000
Bottom rubber 6"
Hi-lift for torsion only
Universal hinge plates
Chain hoist
Pull chain
Low headroom torsion front and rear
Continuous angle 1,1/2" x 4,1/2" x 12 gauge galvanized
Perforated angles 1',1/4" x 1',1/4' x 10'


Edmonton and Area Mobile New Commercial Industrial Overhead Garage Doors Edmonton

Door Surgeon Mobile New Commercial Industrial Overhead Garage Doors Edmonton provided to Edmonton and area:

Northeast Edmonton, Northwest Edmonton, Southeast Edmonton, Southwest Edmonton as well as surrounding areas: St. Albert, Fort Saskatchewan, Sherwood Park, Beaumont, Nisku, Leduc, Acheson, Stony Plain, Spruce Grove and surrounding areas.



JJ - Door Surgeon's Operations Manager:

New Commercial Industrial Overhead Garage Doors installer



JJ started with Door Surgeon in 2008 and has worked reliably. He came to Door Surgeon with a variety of door installation skills and grew his abilities by taking on new challenges in both residential and commercial garage door repair and installation. JJ is the go to man for all that is new commercial industrial overhead garage doors, whether it's installation of new overhead commercial garage doors, repair parts for commercial overhead garage doors or overhead garage door motors, JJ is an expert.

While JJ does spend a small amount of time in the shop helping customers, supervising and training his crew and providing budget quotes he also spends a good deal of time out in the field renovating and repairing commercial industrial overhead garage doors. Often JJ has been the expert to correct other's problems and or rebuild an entire face of a commercial overhead garage door so that the new door will work properly and safely.


Garage Door Assembly and Components - 3 min

© Door Surgeon 2019 | No content may be used without permission.